$projecthp

Search:

Type: Posts; User: Corvette95; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Help with clipping a/c compressor connector to correct location/bracket LT5 ZR-1

    Finishing the refurbish of my low mileage 90 ZR-1. I have the secondary installed. The A/C compressor is plugged up correctly and the connectors is in the right place from multiple photos, including...
  2. Replies
    1
    Views
    412

    doubt it, different design, though similar...

    doubt it, different design, though similar "general look"
  3. Replies
    3
    Views
    2,174

    Gordon is having a school next month, I am...

    Gordon is having a school next month, I am registered
  4. The 95 and 96 ebtcm pump is one unit pump and...

    The 95 and 96 ebtcm pump is one unit pump and computer controller, BUT they do come apart, I image in a pinch you could use a 96 pump take it apart and use the 95 computer after you attach it to the...
  5. Replies
    6
    Views
    1,798

    Help! Sent mine to Bilstein two month ago, they just...

    Sent mine to Bilstein two month ago, they just called me today, gave me multiple options and discount for the delayed response. Said they would be ready in three days.
  6. All my problems were traced down to 95 and 96...

    All my problems were traced down to 95 and 96 having different part numbers and programming and not being compatable. OBD1 vs OBD2 . Fit is identical - compatibility is NOT!
  7. Need absolute final word on part # 1995 ABS EBTCM Pump

    1995 Factory service manual is wrong - shows old design (pre-94), 1996 manual correct. Some GM dealers swear the 1995 is a stand alone pump as is the 96 pump. I know the LT5 (mine is LT1) is...
  8. Replies
    8
    Views
    2,504

    If original poster got his sensor I need a late C4 BLUE right front sensor

    corvette95@charter.net
  9. Replies
    30
    Views
    10,981

    I know this is an OLD thread but

    I need a right front 96blue sensor part#gm88959445 label L88959445b and tx#rf002793
    corvette95@charter.net
    this sensor is BLACK not white with the blue label
  10. Replies
    9
    Views
    6,915

    Help! mu solution was to remove the headlights so you...

    mu solution was to remove the headlights so you can close and adjust the hood with it aligned. its a pain , must use rachet wreches but it finallyo worked for me
  11. Question: normal oil pressures in 94 LT1 according to Alldata....

    I know this is an old thread but my oil pressure keep reading low, I replaced the pump with stock pump this past weekend with same pressure reading. My alldata subscriptions says pressures are:...
  12. Replies
    4
    Views
    1,269

    My top just did the same thing on my 95 ncrs low...

    My top just did the same thing on my 95 ncrs low mileaege car.
  13. oops, yes , passenger seat

    oops, yes , passenger seat
  14. NO! do NOT plug the new motor up before you...

    NO! do NOT plug the new motor up before you install it, if the angle is wrong you can gently turn the blend door shaft that stick down from the heater box. The blend door motor is right about where...
  15. Little tip, set your temperature to 90 BEFORE you...

    Little tip, set your temperature to 90 BEFORE you pull then blend motor. :w
  16. pull the lower trim panel, then turn yourself...

    pull the lower trim panel, then turn yourself upside down with the seat bottom out and take a 5.5mm socket and they are almost hand tight, getting it out is easy....lining the blend door motor up...
  17. Replies
    9
    Views
    6,915

    Help! Did you get the bumper corner / hood corner to...

    Did you get the bumper corner / hood corner to align? If so how? I have the same problem on my 94
  18. Here is the latest. The 96 blend door actuator is...

    Here is the latest. The 96 blend door actuator is different (of course) .....see the little BLUE gear in your photo, thats what tells the programmer where the door position is, the 96 doesnt have...
  19. BTW, if during the calibration cycle, it turns to...

    BTW, if during the calibration cycle, it turns to 60 then 90, from MEMORY, I dont think mine is doing that cycle upon initial start up from battery disconnected. I think it goes to one side and stop...
  20. Yes, I do have multimeter, I will check and post....

    Yes, I do have multimeter, I will check and post. thanks!
  21. How does the programmer know where the temo motor...

    How does the programmer know where the temo motor is at? I know the motor sends a position back but has does IT calibrate itself?
  22. connector was good , next step is to check wires...

    connector was good , next step is to check wires going into programmer?
  23. I will check the connector in the morning, thanks...

    I will check the connector in the morning, thanks for the help. I have had a call into Gordon Killebrews new tech web site that I am a member but havent gotten a response yet
  24. outside temp is reading ok. The blend motor has...

    outside temp is reading ok. The blend motor has "marks" on its facing in about the 10 and 2 o'clock position each being full hot and full cold respectively. The motor will go to either side and try...
  25. I have followed diag tree in factory service...

    I have followed diag tree in factory service manual haven't seen reference to outside temperature sensor , I haven't noticed if it wasn't working. I have a tech2 I will check in car display and...
Results 1 to 25 of 59
Page 1 of 3 1 2 3