$projecthp

Search:

Type: Posts; User: Tom Bryant; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds; generated 48 minute(s) ago.

  1. Replies
    6
    Views
    194

    Welcome! Congrats on the new project. Tom

    Welcome!

    Congrats on the new project.

    Tom
  2. Replies
    1
    Views
    102

    Welcome to the Corvette Action Center. The...

    Welcome to the Corvette Action Center.

    The only column I have not in a car is a 1974 tilt/telescopic and it's about 34" collapsed. Not sure what it extends to. Hopefully someone will have a firm...
  3. Replies
    2
    Views
    1,300

    Welcome to the Corvette Action Center. I'll be...

    Welcome to the Corvette Action Center. I'll be checking out that fFacebook group.

    Tom
  4. Replies
    2
    Views
    198

    Help! I can't find a 1969 listing with 3 lines. Here...

    I can't find a 1969 listing with 3 lines. Hereis one for a 1970 I found and there are a couple more on this page also listed for 70 or newer that have different 3 line configurations. Any of these...
  5. Replies
    3
    Views
    243

    Make sure battery cables are clean and tight.

    Make sure battery cables are clean and tight.
  6. Thread: Radio

    by Tom Bryant
    Replies
    2
    Views
    223

    I would suspect the previous owner had an...

    I would suspect the previous owner had an aftermarket radio in there he had to creativity wire in and he removed it when he decided to sell the car. He attempted to reinstall the original but didn't...
  7. Replies
    3
    Views
    228

    Help! How old are your tires?

    How old are your tires?
  8. Help! That flat top plate is hard to seal. I went to...

    That flat top plate is hard to seal. I went to Harbor Freight and got 2 big C clamps. No leaks after that.
  9. Help! Did you use DOT 3 fluid? I have always had some...

    Did you use DOT 3 fluid? I have always had some trouble getting a correct pedal on a C2 or C3 until I bought a pressure blender. If you aren't with your pedal travel you can probably borrow or rent...
  10. Replies
    10
    Views
    381

    Help! I can see that. There has to be enough shims on...

    I can see that. There has to be enough shims on both sides so the trailing arm can't move back and forth on the bolt.To increase toe in you would have to remove a shim from the inside and install a...
  11. Replies
    10
    Views
    381

    Help! I wasn't aware that the car had been restored....

    I wasn't aware that the car had been restored. Taking it apart at least determines that no short cuts were taken. Check around and find an alignment shop that is experienced with Corvettes and take...
  12. Replies
    10
    Views
    381

    Help! There is a metal sleeved rubber bushing in that...

    There is a metal sleeved rubber bushing in that front eye where the bolt with the shims goes through. If that rubber is degraded that arm will move around on the bolt. If they are original, they...
  13. Replies
    10
    Views
    381

    Help! Check your trailing arm bushings. If they are...

    Check your trailing arm bushings. If they are deteriorated and allowing the front of the arm to move around that will steer it all over the place. They will move one way under acceleration and the...
  14. Replies
    2
    Views
    314

    Love the video.

    Love the video.
  15. Replies
    4
    Views
    301

    Help! Is the part you need on this page? Horn parts...

    Is the part you need on this page? Horn parts
  16. I can't find anything older than 1968.

    I can't find anything older than 1968.
  17. Help! Welcome to the Corvette Action Center The...

    Welcome to the Corvette Action Center

    The caliper piston seals are leaking. More than likely you will need to get rebuilt calipers for the rear. Most rebuilts are stainless steel sleeved so they...
  18. Replies
    10
    Views
    3,205

    Do you have a frame repair shop close by? They...

    Do you have a frame repair shop close by? They can get your car set up on a frame table and get everything positioned exactly where it needs to be according to specifications before welding the tab...
  19. Replies
    5
    Views
    265

    Sounds like you did some smart trading. Welcome....

    Sounds like you did some smart trading. Welcome.

    Tom
  20. Replies
    6
    Views
    459

    Welcome Mike!

    Welcome Mike!
  21. Replies
    4
    Views
    427

    I wouldn't worry about it. The lock washer won't...

    I wouldn't worry about it. The lock washer won't hurt anything.
  22. Replies
    1
    Views
    294

    That looks like a fun car.

    That looks like a fun car.
  23. Replies
    9
    Views
    545

    Have you read this thread yet? 84 ECM...

    Have you read this thread yet? 84 ECM
  24. Replies
    4
    Views
    427

    I just watched a video on Utube and the filter...

    I just watched a video on Utube and the filter does not clamp up tightly once the bolt is tight.
  25. Replies
    3
    Views
    385

    Help! So I assume you don't need to remove the cable...

    So I assume you don't need to remove the cable from the rod now? I haven't been able to find a picture you need but just going from memory and it's been a long time since I last put one of these...
Results 1 to 25 of 491
Page 1 of 20 1 2 3 4