$projecthp

Search:

Type: Posts; User: Jack64; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    334

    Tom, Initial inspection indicates: Cable tight...

    Tom,
    Initial inspection indicates:
    Cable tight at firewall/on pulley
    Also, seems tight at midpoint of frame, and at rear.

    Will try to get under car today, follow cable, and see if can figure...
  2. Replies
    5
    Views
    334

    Tom, No, the car readily rolls. All brake...

    Tom,
    No, the car readily rolls.
    All brake parts/drums are new, done when frame off restoration completed 2019.

    There is simply no resistance when I pull the handle. It is as if something is not...
  3. Replies
    5
    Views
    331

    Purchased my '64 Coupe when I was 22 years old.No...

    Purchased my '64 Coupe when I was 22 years old.No power steering possible because of its high performance engine, 327/365hp.

    50 years later it has been completely restored.
    My first few drives...
  4. Replies
    10
    Views
    839

    Help! Couple of thoughts: Check timing, initial and...

    Couple of thoughts:
    Check timing, initial and total (once running)
    Make certain carburetors properly adjusted, chokes operating.

    Good Luck!
  5. Replies
    5
    Views
    334

    Parking Brake Issue

    Put my '64 Coupe up for the Winter.
    Other day, I planned to roll it back a bit to change tire positioning.
    As I released the hand brake, it had NO resistance.
    The handle slid as if it wasn't...
  6. Replies
    9
    Views
    4,561

    Help! Installed the Luk 04-021 last weekend. What a...

    Installed the Luk 04-021 last weekend.
    What a difference.

    Turned out the clutch removed was a 3 fingered pressure plate, and marks clearly indicated where the throw-out bearing was making uneven...
  7. Replies
    9
    Views
    4,561

    Help! Thanks again, Tom. 04-021 it is.... Regards

    Thanks again, Tom.
    04-021 it is....
    Regards
  8. Replies
    9
    Views
    4,561

    Help! Tom, Are you able to check with your friends...

    Tom,
    Are you able to check with your friends that installed the Luk clutch in their 327 to determine the model they used?
    Was it 04-021 or 04-084?

    Many thanks..
  9. Replies
    9
    Views
    4,561

    Help! Thanks, Tom. Luk it is based upon my research...

    Thanks, Tom.
    Luk it is based upon my research and your recommendation
  10. Replies
    9
    Views
    4,561

    Help! Clutch Recommendation

    Must replace clutch.
    327/365 hp, 4 speed, 3.70 rear.

    Car used for highway, town and country driving.
    No racing, however would like to use the power to get up to speed.

    Do not want heavy leg...
  11. Replies
    4
    Views
    4,467

    Help! Thanks....car on lift over weekend, clips are in...

    Thanks....car on lift over weekend, clips are in place. This must have been extra left on frame rail
  12. Replies
    4
    Views
    4,467

    Help! Thanks, guys. Hope to have car on lift next few...

    Thanks, guys.
    Hope to have car on lift next few days and will examine brakes, as I think it is a clip for a brake line.
    Thank you
  13. Replies
    4
    Views
    4,467

    Help! Can You Identify?

    Found this on my driveway.
    Did it come from '64 Coupe?
    If so, what is it?

    Thank you
    2626426263
  14. Thread: Hard Shifting

    by Jack64
    Replies
    3
    Views
    4,403

    Help! Thanks, Tom. Heading to shop Tuesday. Battling...

    Thanks, Tom.
    Heading to shop Tuesday.
    Battling torn up knee so unable to work on.
    Will update
  15. Thread: Hard Shifting

    by Jack64
    Replies
    3
    Views
    4,403

    Help! Hard Shifting

    '64 has 502 miles since frame off restoration.
    Engine, rear, transmission re-built.
    New clutch.

    Hard shifting, especially into reverse.
    Must depress pedal to floor.
    Clutch seems to not fully...
  16. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, Don't recall anything being present to...

    LLC5,
    Don't recall anything being present to insulate when I removed clock a couple months ago.
    Perhaps that's why it didn't work last time it was on the road 43 years ago!!

    Off to Corvette show...
  17. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, You are correct. The terminal attached...

    LLC5,
    You are correct. The terminal attached with the nut is in contact with the case.

    A) Must we isolate the nut as well as the terminal?
    B) Best way to isolate...rubber washer?

    Regards
  18. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! Brake Lights Yes, with the switch separated, the...

    Brake Lights
    Yes, with the switch separated, the brake lights went out.
    Good indication, am guessing, the switch is the problem.
    Will hook up switch and adjust tomorrow. May correct.

    26227Clock...
  19. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, Have unsuccessfully spent several hours...

    LLC5,
    Have unsuccessfully spent several hours trying to remove brake light switch. Between my artificial hip, my torn meniscus, and my large hands, it did not go well.

    Want to reconnect switch to...
  20. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, unable work on switch other than observe...

    LLC5, unable work on switch other than observe plunger.
    Dealing with torn meniscus in knee. Will try at it again and report back
    Rgds
  21. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! Continuing saga: Brake Lights remain on....

    Continuing saga:
    Brake Lights remain on.
    Checked brake switch, operating fine. Plunger moves easily
    Might it be defective?.

    Otherwise I do have all other lights, parking/directional,...
  22. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! OK, an update: 1) All fuses have been replaced...

    OK, an update:
    1) All fuses have been replaced
    2) The power tap was attached to the cold side.
    It would appear this tap operates the directional lights, which were restored after tap installed.
    ...
  23. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, I believe the power tap was attached to...

    LLC5,
    I believe the power tap was attached to the right side of the 3 amp fuse.
    Would this be the fused side?

    All fuses replaced. Awaiting arrival of power tap.
    Rgds
  24. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! LLC5, Front signals do NOT come on, just rear...

    LLC5,
    Front signals do NOT come on, just rear brake lights.
    Do not have 4 way flashers
    Currently away from car. Will unplug stoplight switch tomorrow and update.

    Have new puller and fuse taps...
  25. Thread: Power To Clock

    by Jack64
    Replies
    26
    Views
    4,952

    Help! Well, making some progress, and regressing as...

    Well, making some progress, and regressing as well.

    Replaced all fuses except top 10 amp. (My puller broke)
    Now have interior lights, however, the brake lights will NOT go off.
    There was a...
Results 1 to 25 of 62
Page 1 of 3 1 2 3