$projecthp

Search:

Type: Posts; User: Tom Bryant; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    10
    Views
    389

    Help! Code 12 is "no reference pulses to ECM" This code...

    Code 12 is "no reference pulses to ECM" This code is not stored in memory and will only flash while the fault is present. Check again your 4 post terminal distributor connector. Check closely that...
  2. Question: There is an article in the Knowledgebase section...

    There is an article in the Knowledgebase section of this site by John Hinkley on the A. O. Smith body operation. Here is the link----> A. O. Smith
    He says half were built at St. Louis and half at...
  3. Replies
    2
    Views
    139

    I'd think mid to upper 40s. It looks like a...

    I'd think mid to upper 40s. It looks like a really good car from the photos.

    Tom
  4. Help! Welcome to the CAC If the cowl is missing it's...

    Welcome to the CAC

    If the cowl is missing it's likely on another frame now and since the cowl has the trim tag and vin plate under the dash it is probably titled to someone else. May have been...
  5. Replies
    10
    Views
    389

    Help! If the m/c sol is causing a lean mixture that...

    If the m/c sol is causing a lean mixture that would explain the o2 lean code. I suggest that before you throw any money at that carb do the tests I outlined in post 5 of this thread. Do this to see...
  6. Replies
    7
    Views
    299

    Welcome. Tom

    Welcome.

    Tom
  7. Replies
    5
    Views
    272

    Welcome to the CAC. Tom

    Welcome to the CAC.

    Tom
  8. Replies
    4
    Views
    148

    Welcome to the Corvette Action Center! Tom

    Welcome to the Corvette Action Center!

    Tom
  9. Thread: cam ???

    by Tom Bryant
    Replies
    3
    Views
    193

    Could very well be a Crane grind. Tom

    Could very well be a Crane grind.

    Tom
  10. Thread: cam ???

    by Tom Bryant
    Replies
    3
    Views
    193

    They are pretty close. The L82 has 222 vs 214...

    They are pretty close. The L82 has 222 vs 214 degrees degrees intake duration at .050 and 114 degrees LSA vs 112 for the Summit cam but otherwise they are about the same. I doubt you could tell the...
  11. Thread: EGR delete

    by Tom Bryant
    Replies
    6
    Views
    256

    This diagram says it's a '79 Corvette but who...

    This diagram says it's a '79 Corvette but who knows? The gas tank vents to the vapor canister. Vapors are stored in the canister until the engine is run then are drawn into the carb and burned. The...
  12. Thread: EGR delete

    by Tom Bryant
    Replies
    6
    Views
    256

    Here's a diagram I found on the Google box. Back...

    Here's a diagram I found on the Google box. Back when we had annual inspections I'd unplug the EGR hose and push a small ball bearing up the hose to block it off. Then plug the hose back in. Nobody...
  13. Replies
    10
    Views
    389

    Help! Scans of manual.

    Scans of manual.
  14. Replies
    10
    Views
    389

    Help! The code 23 is a Mixture control solenoid thing...

    The code 23 is a Mixture control solenoid thing and I can't see how that would keep the engine from turning with the starter. It may be pointing to other drivability issues though. The Mixture...
  15. Replies
    10
    Views
    389

    Help! Are you sure you didn't fry the ECM? Are you...

    Are you sure you didn't fry the ECM? Are you getting codes?

    Tom
  16. Replies
    4
    Views
    443

    Question: It would be the input shaft more than likely....

    It would be the input shaft more than likely. NAPA sells a repair sleeve for that. They also sell sleeves for the shifter shafts but usually new o-rings will fix them. The rear would be a sleeve for...
  17. They will be stiffer than the old ones for awhile...

    They will be stiffer than the old ones for awhile but you should be able to move them with your hands.

    Tom
  18. Replies
    8
    Views
    407

    Very unlikely. I've never heard of a late '79...

    Very unlikely. I've never heard of a late '79 having 80 wheels originally. A previous owner probably swapped them on, maybe even replacing rally wheels. Another thought is that a lot of the brushed...
  19. Replies
    8
    Views
    407

    Also be aware that the 76-79 wheels had a brushed...

    Also be aware that the 76-79 wheels had a brushed finish originally and the 80-82 had a polished finish.

    Tom
  20. Replies
    11
    Views
    716

    The ball is welded to the end of the cable or...

    The ball is welded to the end of the cable or possibly crimped on. I'm not sure if you can see the end of the cable at the handle by looking under the instrument panel or not.
  21. Replies
    11
    Views
    716

    Could be that the ball has come off the top end...

    Could be that the ball has come off the top end of the cable. I've seen that happen.
  22. Video: Cool stuff.

    Cool stuff.
  23. Replies
    11
    Views
    716

    Top end of the cable also has a ball welded to it...

    Top end of the cable also has a ball welded to it and that would fit in a clevis or slot on the hand brake lever. The housing has a steel sleeve on the top end that either fits in a receiver in the...
  24. Replies
    7
    Views
    602

    Please post some photos when you get them. I had...

    Please post some photos when you get them. I had a friend back in '63 that bought a new white convertible.

    Tom
  25. That looks nice with the 66 wheel covers. Never...

    That looks nice with the 66 wheel covers. Never saw that before.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4