$projecthp

Search:

Type: Posts; User: Tom Bryant; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds; generated 16 minute(s) ago.

  1. Replies
    6
    Views
    3,588

    Welcome to the CAC. What is your intended...

    Welcome to the CAC.

    What is your intended usage? Just driving or racing?

    Tom
  2. Replies
    6
    Views
    192

    Welcome to the CAC. Looks like a couple of fun...

    Welcome to the CAC. Looks like a couple of fun cars.

    Tom
  3. Replies
    2
    Views
    185

    Help! I did the '81 two years ago and no amount of...

    I did the '81 two years ago and no amount of pedal pumping would get all the air out. I finally gave up and bought a pressure bleeder. Should have bought one years ago. It was so quick and easy.
    ...
  4. Replies
    9
    Views
    360

    Help! When it won't start is there raw fuel running...

    When it won't start is there raw fuel running down inside the carbs? Is the fuel filter bowl full? Is the choke opening fully? How long do you run it after it initially starts ok before you shut it...
  5. Replies
    1
    Views
    222

    Not sure what you mean. Did you change steering...

    Not sure what you mean. Did you change steering columns on your '59?
  6. I should get one of those. Probably the closest...

    I should get one of those. Probably the closest I'll ever get to owning one.

    Tom
  7. Replies
    10
    Views
    378

    Welcome to the CAC Tom

    Welcome to the CAC


    Tom
  8. Thread: Trim tag

    by Tom Bryant
    Replies
    3
    Views
    255

    Well I took the total number of 1976 Corvettes...

    Well I took the total number of 1976 Corvettes built and subtracted the numbers of cars built in known 1976 production colors (including the 1 code 39 Dark Green that some books don't show) and ended...
  9. If your seals are not letting grease out then...

    If your seals are not letting grease out then they won't let water in. The outer seal is shielded by the rotor and the inner seal is shielded by the control arm so there is no way to apply a high...
  10. Replies
    3
    Views
    403

    I'm sure there is someone out there that needs...

    I'm sure there is someone out there that needs your part. It may take some time though.

    Tom
  11. Replies
    7
    Views
    380

    Welcome to the CAC. Nice pair of Corvettes. Tom

    Welcome to the CAC. Nice pair of Corvettes.

    Tom
  12. Replies
    6
    Views
    335

    Welcome to the CAC. Tom

    Welcome to the CAC.

    Tom
  13. Replies
    5
    Views
    310

    Welcome Ralph. It isn't often that I run into...

    Welcome Ralph.

    It isn't often that I run into somebody that has had their solid axle longer than I.

    Tom
  14. I've seen a lot worse. I wonder if it would be...

    I've seen a lot worse. I wonder if it would be possible to bond a strip of fiberglass sheet about 1/4 in thick to the back of that area holding it straight.

    Tom
  15. Replies
    7
    Views
    572

    I'm going to move this thread to the C6 Forum. It...

    I'm going to move this thread to the C6 Forum. It will get more attention there.

    Tom
  16. Replies
    7
    Views
    572

    I can't help you with the paddle shift but ACI...

    I can't help you with the paddle shift but ACI makes some nice spoilers and other parts for the C6. We toured the facility during a past CAC Cruisefest and it is a quality operation.

    ACI
  17. Replies
    7
    Views
    316

    The 3735236 crank was a forged 3.00 inch stroke...

    The 3735236 crank was a forged 3.00 inch stroke crank used in 283 engines. I don't think you see any cast 283 cranks until up in the mid '60s. This casting number was used under part number 3760042...
  18. I usually have a few jumper wires I have made up...

    I usually have a few jumper wires I have made up with wire and some alligator clips that you can get at any auto parts store. You will be surprised how often you use them once you have them. Hook one...
  19. Thread: Newbie

    by Tom Bryant
    Replies
    5
    Views
    336

    Welcome to the CAC. Glad you are having a lot of...

    Welcome to the CAC. Glad you are having a lot of fun with your Corvette.

    Tom
  20. Replies
    6
    Views
    555

    Welcome to the CAC. That's going to be a fun...

    Welcome to the CAC. That's going to be a fun project. I'd give that polish a try and see how it comes out. Sometimes it's necessary to do a light color sanding first but it all depends on the...
  21. Replies
    6
    Views
    348

    Welcome to the CAC. I'm also in my 70s and have...

    Welcome to the CAC. I'm also in my 70s and have had my '59 since '69. Others have came and went but the '59 is family. It may even see the road again someday. Congrats on the Z06. I hope you and your...
  22. Video: This is good stuff. I have one of these to do...

    This is good stuff. I have one of these to do someday. I replaced my original way back when good used ones were still available. $35.00 well spent. The original is stored in the basement.

    Tom
  23. Replies
    3
    Views
    340

    Get it on a lift. Start the engine and check for...

    Get it on a lift. Start the engine and check for exhaust leaks. This also gives you a chance to check the under side of the body panels for damage repair, check the brakes for leaks (right side...
  24. Thread: Tool Rental

    by Tom Bryant
    Replies
    4
    Views
    409

    I don't have those tools but have you checked...

    I don't have those tools but have you checked with Auto Zone or O'Reilies? I know that they have loanout tools for many operations. A valve spring compressor is common enough that I would think they...
  25. Replies
    4
    Views
    345

    That color is Code 28 Frost Blue Or Light Blue...

    That color is Code 28 Frost Blue Or Light Blue depending where you look. I've seen it called both names in the same publication. There was only one locally back when they were almost new but 3203...
Results 1 to 25 of 491
Page 1 of 20 1 2 3 4