$projecthp

Search:

Type: Posts; User: frank_nesta; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    1,693

    Hey RickC4, My comments were were done in August...

    Hey RickC4, My comments were were done in August 2016 and for a C3. I am not even sure that the Link provided even exists.
  2. Replies
    3
    Views
    658

    First make sure the fuse is out. You need to...

    First make sure the fuse is out. You need to take the driver side panel on the side of the console off. Then hold the bottom side of the cigar lighter so it does not spin. Good luck.
  3. There is another method. See what happens when...

    There is another method. See what happens when you get to sleep on something?

    There is a code that is stamped into the differential case. Its located in between the leaf spring plate that is...
  4. To answer your question. It can be done, but you...

    To answer your question. It can be done, but you need to match the year of the car, engine size, transmission and reared. Then match the RPM and speed. So it is not easy.

    douglasamariani has...
  5. Just a little clarification. Jack the car up so...

    Just a little clarification. Jack the car up so both wheels will turn.

    Posi: Jack both wheels off the ground. Turn one wheel 1 complete turn.
    - Count the turns on the drive shaft.

    Non-posi:...
  6. I found this. I hope this helps. Removing...

    I found this. I hope this helps.

    Removing dents from plastic bumpers | Search Autoparts
    Removing dents from plastic bumpers | Search Autoparts
  7. Replies
    2
    Views
    628

    I would pull the delay and see if that is causing...

    I would pull the delay and see if that is causing the problem?
  8. My question is did they paint the car with the...

    My question is did they paint the car with the bumper in that condition? If they did the the paint might crack trying to get it back to straight. if the car was painted with the bumper in that...
  9. I don't know if it is the photo or the bumper. ...

    I don't know if it is the photo or the bumper. But, the bumper looks like it is pulled out from the bottom center causing the wave. The bottom edge of the bumper should be straight across from left...
  10. Replies
    10
    Views
    5,164

    OK you peaked my interest. How do the Feds catch...

    OK you peaked my interest. How do the Feds catch you?
  11. Replies
    7
    Views
    3,603

    Question: This might be interesting on the subject 12 bolt...

    This might be interesting on the subject 12 bolt conversion. Pertains to a Camaro!


    How to install Positraction and give your muscle car tire-frying capability
  12. Replies
    3
    Views
    2,793

    Do this google search there are plenty of answers...

    Do this google search there are plenty of answers out there.

    location of the power window circuit breaker on a 1974 corvette
  13. Replies
    1
    Views
    3,588

    Help! I am not sure if I have the answer, but I have...

    I am not sure if I have the answer, but I have some good questions.

    Are you using the Car's Wifi? Are you using Apple Play? If you are to one or both, try disconnecting your phones Wifi. I...
  14. Replies
    5
    Views
    1,898

    Thanks again Tom. I have learned that it is...

    Thanks again Tom.

    I have learned that it is not in the AIM because the knuckle wheel hub assembly was delivered to the factory as a assembly.
  15. Replies
    5
    Views
    1,898

    if you do that I would really appreciate it. ...

    if you do that I would really appreciate it. Thank You.
  16. Replies
    5
    Views
    1,898

    Missing Diagram?

    I am redoing my front brakes and went to my trusty AIM and can not find a detailed diagram for 1977 corvette steering knuckle wheel hub assembly diagram. I was looking for the caliper bracket dust...
  17. Replies
    5
    Views
    1,226

    It is not impossible. It all depends on what you...

    It is not impossible. It all depends on what you want to spend. You need to find a rear deck lid similar to the one in the link below or get a rear clip from a 1974 - 1977 Corvette. I had a...
  18. Replies
    1
    Views
    770

    Attached is a Willcox headlight diagram for a 69...

    Attached is a Willcox headlight diagram for a 69 Corvette. Since your 69 has only one relay (later models have 2 relays) that does not seem to be the problem. I would trace each hose back to the...
  19. Thread: C3 Brakes

    by frank_nesta
    Replies
    13
    Views
    975

    Yes , you need two bleed hoses connected to each...

    Yes , you need two bleed hoses connected to each bleed nipple on the caliber halves. With someone on the brake pedal , open each bleed nipple in turn, close off with the pedal on the floor. repeat...
  20. Thread: C3 Brakes

    by frank_nesta
    Replies
    13
    Views
    975

    When you carry out the bleeding are the back ones...

    When you carry out the bleeding are the back ones more difficult than the front? If so, bleed both halves of each caliber at the same time . Good luck.[/QUOTE]

    I have never heard of that. How is...
  21. Thread: C3 Brakes

    by frank_nesta
    Replies
    13
    Views
    975

    Rotor Runout

    Rotor runout is another cause for air being sucked into the calipers. I believe runout should not be more that .005".
  22. Replies
    4
    Views
    778

    They do sit higher than stock seats. Taller...

    They do sit higher than stock seats. Taller people with t-tops on may have a problem. I almost never have my top up.
  23. Replies
    4
    Views
    778

    C6 Seats

    They take some work to get them in the right position. I have the lumbar, booster, and heated seats working. Seat belts are seat mounted and stock mount on the retractor side. Planet Seatbelt made...
  24. Replies
    2
    Views
    1,848

    Question: I agree.

    I agree.
  25. Craft shops also might carry these items.

    Craft shops also might carry these items.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4