$projecthp

Search:

Type: Posts; User: Tom Bryant; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds; generated 46 minute(s) ago.

  1. Replies
    20
    Views
    793

    Yes I'm talking about jumping the relay. Here is...

    Yes I'm talking about jumping the relay. Here is a picture from Wilcox that might help.
  2. Replies
    3
    Views
    286

    I use one on the '81. it takes a good long time...

    I use one on the '81. it takes a good long time to run the battery down but the ecm memory and the radio/clock memory will suck it down over a time. Pull the clock fuse then test it again to see if...
  3. Replies
    20
    Views
    793

    You should have 2 bigger wires on the relay and 2...

    You should have 2 bigger wires on the relay and 2 smaller. One of the bigger is 12 volt with key on and the other goes to the blower motor. Jump across them and see if the motor spins up to full...
  4. Replies
    20
    Views
    793

    This is all you see when installed. Resistor...

    This is all you see when installed. Resistor.
  5. Replies
    20
    Views
    793

    On my '81 this inserts right on top of the a/c...

    On my '81 this inserts right on top of the a/c evap /heater box. Has a plug on it. Here is one for your car from Zip. Original GM part number was 3942651. You can just remove the 2 screws and pull it...
  6. Replies
    6
    Views
    353

    Welcome to the Corvette Action Center. Tom

    Welcome to the Corvette Action Center.

    Tom
  7. Replies
    20
    Views
    793

    I agree. The resistor has coils of different gage...

    I agree. The resistor has coils of different gage wire that control the motor speed. If one coil burns out you loose that speed.
  8. Help! It would probably be a good idea to check the...

    It would probably be a good idea to check the bulb sockets for corrosion.
  9. Video: Remarkable cleanup.

    Remarkable cleanup.
  10. Question: The early 63 used the same shifter as the 59 to...

    The early 63 used the same shifter as the 59 to 62. The arms on the trans only had one hole for the shifter rods. I seem to remember reading someplace that certain passenger car shift arms would fit...
  11. Help! Since you have checked your grounds did you clean...

    Since you have checked your grounds did you clean the battery cables too? Have you had your battery load tested? Also have you checked the alternator output? Does it move the same or more when you...
  12. Question: There was no RPO number for a color override in...

    There was no RPO number for a color override in those years. To get a non-production paint color or paint/interior color combo you had to go through the COPO program. I don't know of a listing of...
  13. Replies
    3
    Views
    271

    It looks like a decent driver that's had some...

    It looks like a decent driver that's had some dress up mods done. Interior looks very nice. The wood trim is an add on aftermarket thing as are the exhaust tips. Distributor shield is missing.

    If...
  14. Replies
    9
    Views
    346

    No. The diagram shows it in the EFE hose.

    No. The diagram shows it in the EFE hose.
  15. Replies
    9
    Views
    346

    This diagram shows the dist vac to the drivers...

    This diagram shows the dist vac to the drivers side carb pipe like your label shows. The Check valve/thermal switch (on the thermostat housing) hose off the center carb pipe control the EFE actuator...
  16. Replies
    8
    Views
    256

    I forgot about that. Diode Trios went across the...

    I forgot about that. Diode Trios went across the parts counter almost as fast as brush sets and ignition points back then.

    Tom
  17. Replies
    2
    Views
    302

    Help! It looks similar to one I had in the early 80s...

    It looks similar to one I had in the early 80s when I lived in Ft. Wayne. Mine had cut rear wheel wells but not flared and header side pipes. It had Cragers of about the same dimensions as your slots...
  18. Replies
    9
    Views
    346

    That is odd..

    That is odd..
  19. Replies
    9
    Views
    346

    It’s an emissions thing that doesn’t allow vacuum...

    It’s an emissions thing that doesn’t allow vacuum advance until the engine reaches a specific temperature. Does it still work?

    Tom
  20. Question: Of those 3 midyears the '67 would be the best...

    Of those 3 midyears the '67 would be the best investment. The other 2 would both be a lot of fun to own but harder to find a buyer for. I'd want to be in them around 5k to 10k less to be comfortable....
  21. Thread: 427 Day!

    by Tom Bryant
    Replies
    1
    Views
    266

    I noticed that.

    I noticed that.
  22. Thread: small block

    by Tom Bryant
    Replies
    4
    Views
    178

    Welcome to the CAC! Tom

    Welcome to the CAC!

    Tom
  23. Are you sure that car isn't a 69? That block...

    Are you sure that car isn't a 69? That block casting number is for a mid 69 production Corvette 350. I ask because of the engine casting number. The Stingray emblems on the front fenders and the side...
  24. Replies
    3
    Views
    315

    I've never used anything other than GM lubes. The...

    I've never used anything other than GM lubes. The part numbers have changed over the years but the product is what is recommended for a GM posi rear axle. If the other brands meet the same...
  25. Question: Numbers matching correct engine is always easier...

    Numbers matching correct engine is always easier to find a buyer for. Even though the person coming to look at your car may not actually care at all if it has matching numbers he will still use it...
Results 1 to 25 of 490
Page 1 of 20 1 2 3 4