$projecthp

Search:

Type: Posts; User: motorman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    12
    Views
    3,043

    Help! did you scrub the cylinders bores good with soap...

    did you scrub the cylinders bores good with soap and water to get the honing grit out ???
  2. Replies
    22
    Views
    6,921

    like I posted before there is a "O" ring under...

    like I posted before there is a "O" ring under that soft plug that is the seal. I have used fuel proof model pane dope for years with no come backs. gently tap around the edges to peen the area...
  3. Replies
    22
    Views
    6,921

    if you use epoxy make sure it is ethanol safe.

    if you use epoxy make sure it is ethanol safe.
  4. Replies
    1
    Views
    1,315

    Question: the bore should be .375 and the shaft diameter...

    the bore should be .375 and the shaft diameter should be .368
  5. Replies
    22
    Views
    6,921

    clean the area good and seal it with clear fuel...

    clean the area good and seal it with clear fuel proof model airplane dope. there is a O ring under that plug that goes away after years.
  6. Replies
    14
    Views
    3,912

    Question: the new corvette engine uses a oil filter with...

    the new corvette engine uses a oil filter with the filter bypass valve built into the filter so there would some metal like a spring involved.
  7. if you continue to fill the tank after the...

    if you continue to fill the tank after the station pump shuts stop doing this as it is moving the slider into unused area causing the problem. I found this out with my 97. once I stopped force...
  8. Important! correct the panels are painted by robots and the...

    correct the panels are painted by robots and the paint is like it is because of the federal air regulations about what these factories are allowed to put into the air
  9. Question: back in 66 when i tried to sell my 66 450 HP 427...

    back in 66 when i tried to sell my 66 450 HP 427 corvette anyone who wanted to buy it the insurance payments a month were more than the car payments.
  10. Replies
    11
    Views
    3,111

    i understand the lower air flow under the C-7...

    i understand the lower air flow under the C-7 required these extra coolers to help cool the trans and rear gear
  11. Notice: the last good sales year was 2008 and what...

    the last good sales year was 2008 and what happened in 2008 a lot of peoples 401K took a big hit. as a corvette owner since 1959 corvettes are bought with fun money. my corvette club which has about...
  12. Replies
    0
    Views
    989

    paper work for 1965 396

    I have the paper work for a factory delivered 396 vert vin 19467S114271
  13. Replies
    22
    Views
    4,845

    similar to diesel piston design which are DI...

    similar to diesel piston design which are DI except for the valve relief. THANK GOD for computer controlled machine tools
  14. News: I believe that there was a TSB on C-6

    I believe that there was a TSB on C-6
  15. News: corvette and HD have one thing in common, most...

    corvette and HD have one thing in common, most red blooded males would love to have one
  16. Thread: Orange Peel

    by motorman
    Replies
    115
    Views
    19,077

    it will go a GM dealer only auction with a...

    it will go a GM dealer only auction with a statement of the reason for the buy back. post the VIN here so no one else gets the car.
  17. Thread: Orange Peel

    by motorman
    Replies
    115
    Views
    19,077

    you can thank the EPA for it restriction on...

    you can thank the EPA for it restriction on emissions from paint booths for your orange peel
  18. Replies
    4
    Views
    1,364

    Question: after you have it repaired make sure you have 3M...

    after you have it repaired make sure you have 3M protective film installed on the mirrors. no matter what you hear here zaino will not prevent rock damage. :D
  19. Replies
    14
    Views
    2,948

    here is the GM heat shield and they also have one...

    here is the GM heat shield and they also have one for the Q jet
  20. Replies
    14
    Views
    2,948

    there is a check valve in the fuel filter and if...

    there is a check valve in the fuel filter and if you use a filter without one the float bowl will drain down
  21. Replies
    26
    Views
    2,994

    most of the design was dictated by the race teams...

    most of the design was dictated by the race teams need of better aero at speed so they have down force without a lot of drag
  22. Replies
    6
    Views
    3,067

    Question: the corvette engineers at BG told me to set the...

    the corvette engineers at BG told me to set the camber as close to "O" as possible.
  23. Replies
    14
    Views
    2,928

    Question: the stock chevy wheels are counter bored around...

    the stock chevy wheels are counter bored around the stud holes to allow clearance for the spring washers that hold the rotors in place. if your wheels don't have this they will not set flat on the...
  24. Replies
    352
    Views
    110,157

    Poll: i am 78 and on my 11th new corvette since 1959...

    i am 78 and on my 11th new corvette since 1959 and will have a C-7 good lord willing. :D
  25. Replies
    15
    Views
    19,292

    Question: there are articles from Mobil about Mobil 1...

    there are articles from Mobil about Mobil 1 running 250,000 miles with no oil changes except filters.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4