$projecthp
  • Removing crank position sensor
  • Removing crank position sensor
  • Removing crank position sensor
  • Removing crank position sensor

Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 3 of 3
  1. #1
    trebor
    Guest

    Default Removing crank position sensor

    Hi:

    I bought a new o ring for the CPS. I can not get the bolt out that holds the CPS in place. A few questions for anyone who has done this:

    1. Bolt size 8mm yes or no

    2. Did you remove it from the top (sticking arm down passenger side next to power steering resevoir)?

    or

    3. Did you remove it with the car up on ramps from beneath the car?

    4. If yes, did you have to remove crossmember?

    5. Did you use an open end wrench or socket?

    Any other tips greatly appreciated

    trebor

    __________________
    1996 CE LT4, Z51, FE3

  2. #2
    Member So Bay Vetter's Avatar
    Join Date
    Mar 2005
    Location
    El Segundo, CA
    Posts
    372
    Corvette(s)
    1996 Collector LT4
    Post Thanks / Like
    Rides
    0

    Default

    I've done this (from the bottom). I'm guessing you have an oil leak and it's dripping from the CPS? I'll start with the outcome on mine: It was the main bearing seal leaking and dripping off the end of the CPS so in my case, the whole job was for not.

    A mechanic will either remove the balancer pulley or remove the oil pan to gain access to the CPS. Hindsight being 20/20, I would've waited until a repair required one of the above to be done and do it then. Especially since it may be the main and not the CPS!

    But if you're really passionate about an entire day of four letter expletives, here's what I did:

    It's been a few years so I don't remember whether the bolt is an 8 or 10 (sorry) I used a 1/4 drive socket / handle (no clearance for a ratchet) with a makeshift extension on the handle. There's very little throw on the handle and the bolt is about an inch long so it takes a long time to remove. Once it's loose, try putting surgical tubing over the bolt head and spinning it out that way (and back in). And think hard about whether the end justifies the effort, I wish I had

  3. #3
    Member
    Join Date
    Feb 2013
    Location
    USA
    Posts
    30
    Corvette(s)
    1970 coupe 1996 LT4 coupe
    Post Thanks / Like
    Rides
    0

    Default 1996 LT4 crankshaft position sensor

    trebor, did you replace the o-ring seal on your LT4's crankshaft position sensor? Do remember what procedure you used to access the removal and installation? I am going to replace the seal on my LT4 next week, or try to. If you replaced your o-ring did it solve the oil leakage problem? Jim
    Last edited by ZZ1-70 LT4-96; 09-30-15 at 12:26 PM.

Similar Threads

  1. Car cranks but doesnt start
    By Deusxmachine in forum C4 Technical and Performance
    Replies: 50
    Last Post: 08-14-09, 03:04 AM
  2. Help! Opti-Spark Testing??
    By Donne Trav in forum C4 General Discussion
    Replies: 3
    Last Post: 10-04-08, 12:24 PM
  3. Active Handling/ABS Warning Light
    By sandmanmd in forum C5 Technical and Performance
    Replies: 12
    Last Post: 05-11-06, 10:32 PM
  4. Need Throttle Position Sensor Screws!
    By 87Z52 in forum C4 Parts For Sale / Wanted
    Replies: 7
    Last Post: 04-02-06, 08:23 PM
  5. P0336 Crank Angle Sensor Code Set
    By jblowers in forum C4 Technical and Performance
    Replies: 12
    Last Post: 08-12-03, 08:59 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •