• Trunk Key, FOB program step 5/6 will not respond
  • Trunk Key, FOB program step 5/6 will not respond
  • Trunk Key, FOB program step 5/6 will not respond
  • Trunk Key, FOB program step 5/6 will not respond

Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 2 of 2
  1. #1
    New Member
    Join Date
    Nov 2014
    Location
    Manorville, NY
    Posts
    1
    Corvette(s)
    2008 Conv. Jet stream blue 6spd, 1980 red 4spd
    Post Thanks / Like
    Rides
    0

    Default Trunk Key, FOB program step 5/6 will not respond

    I'm sorry for another FOB thread but I could not find an answer to this.

    i am trying to program FOB's 3 & 4. Following either short or long procedure it says to put the key in the receptical near the trunk and turn it 5 times in less than 5 seconds. I am supposed to hear a beep and the DIC should light up with a message.

    It it does nothing. Working FOB is on the console and no cell phones.
    Now what?

    Any suggestions other than a trip to the dealer who will charge me $137.

    Thanks in advance.

  2. #2
    Supporting Dealer MacMulkin Chevrolet's Avatar
    Join Date
    Aug 2007
    Location
    Nashua NH
    Posts
    258
    Corvette(s)
    1990 Corvette ZR-1
    Post Thanks / Like
    Rides
    0

    Default

    What receptical near the trunk are you talking about?

    The owners' manual states to place the fob in the receptacle on the steering column...
    -----------------------------------------------------------------------------------------------------

    Programming the Transmitters to the Vehicle

    Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to eight transmitters programmed to it.

    Programming with a Recognized Transmitter


    A new transmitter can be programmed to the vehicle when there is one recognized transmitter.

    1. The vehicle must be off and both the recognized and new transmitters must be with you.
    2. Remove the key base from the recognized RKE transmitter.
    3. Place the recognized transmitter in the cupholder.
    4. Insert the vehicle key into the key cylinder above the license plate.
    5. Open the hatch/trunk.
    6. Turn the key five times within 10 seconds.
    7. The DIC displays READY FOR REMOTE # 3 or 4, up to 8.


    3403755-jpg


    1. Place the new transmitter in the steering column transmitter pocket with the buttons facing up and the base toward the opening facing the passenger side.
    2. Press the ENGINE START/STOP button.
    3. The DIC displays READY FOR REMOTE # 4 or 5, up to 8.
    4. Press K on each newly programmed transmitter to complete the process.
    5. To program additional transmitters, repeat Steps 8–11. Press and hold the ENGINE START/STOP button for 12 seconds if programming is complete.


    Return the key base back into the RKE transmitter.

    Programming without a Recognized Transmitter

    If there are no currently recognized transmitters available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all transmitters to be programmed must be present.


    1. The vehicle must be off.
    2. Remove the key from the transmitter and insert the vehicle key into the key cylinder above the license plate.
    3. Open the hatch/trunk.
    4. Turn the key five times within 10 seconds.

    The DIC message displays REMOTE LEARN PENDING PLEASE WAIT.


    1. Return key base back into the RKE transmitter.
    2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button.

    The DIC reads REMOTE LEARN PENDING, PLEASE WAIT.


    1. Repeat Step 6 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC display should now show READY FOR REMOTE #1.


    3403755-jpg


    1. Place the new transmitter in the steering column transmitter pocket with the buttons facing up and the base toward the opening facing the passenger side.
    2. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the new transmitter.
    3. Remove the transmitter from the transmitter pocket and press Q or K on the transmitter.


    To program additional transmitters, repeat Steps 9–10. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
    Attached Thumbnails Attached Thumbnails 3403755-jpg  
    We are one of the top Corvette Dealers in the world!

    MacMulkin Corvette does NOT charge any admin or doc fees. The price we quote is the price you pay.


    Call 603-888-1121 or Contact Us today!
    Corvette Incentives
    MacMulkin Corvette Site

    Follow Us On:
    Facebook
    Pinterest
    Twitter

    Save
    Likes Scottsredvette liked this post

Similar Threads

  1. Help! 2006 Z06 will not respond to fob
    By Red car Frank in forum C6 Z06 Discussion
    Replies: 1
    Last Post: 08-01-17, 10:29 AM
  2. Replies: 0
    Last Post: 06-22-17, 03:00 PM
  3. Replies: 16
    Last Post: 08-15-12, 10:49 AM
  4. C5 trunk lid (inside trunk) wanted.
    By mr_dakota in forum C5 Parts For Sale / Wanted
    Replies: 0
    Last Post: 08-26-05, 07:34 AM
  5. Guage change-step by step-large pics, be patient
    By 69MyWay in forum C3 Technical and Performance
    Replies: 9
    Last Post: 11-16-01, 06:53 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •