• Better aftermarket heads for my  77 L48
  • Better aftermarket heads for my  77 L48
  • Better aftermarket heads for my  77 L48
  • Better aftermarket heads for my  77 L48

Results 1 to 8 of 8
  1. #1
    Member stevolwevol's Avatar
    Join Date
    May 2015
    Location
    Michigan
    Posts
    172
    Corvette(s)
    1977 light blue
    Post Thanks / Like
    Rides
    0

    Default Better aftermarket heads for my 77 L48

    I am considering replacing my stock heads to a good flowing aftermarket heads. I'm looking for better flow, and higher compression. I don't really know where to start, but I want to replace the cam also. This is for street use. Any suggestions would be appreciated.
    Likes JAGwinn liked this post

  2. #2
    Administrator Tom Bryant's Avatar
    Join Date
    Nov 2000
    Location
    Edgerton, Ohio, United States
    Posts
    6,990
    Corvette(s)
    1959 black 270hp (9/2/69) 1981 Beige L81(10/20/80)
    Post Thanks / Like
    Rides
    2

    Default

    Do you want to go to aluminum or stick with an iron head? To run premium pump gas about 9.5 with iron and 10.5 with aluminum would be your max cr. The Chevy Vortec iron head would be a good upgrade for a mild build. I think GM still sells them drilled for both a Vortec intake pattern and traditional small block pattern so you won't have to change intake manifolds.
    NCRS 1360.............SACC 2082.............C1 Registry..............L81 Registry
    1959 Chevrolet Corvette 1981 Chevrolet Corvette , 350 L81 automatic Frost Beige

  3. #3
    Member stevolwevol's Avatar
    Join Date
    May 2015
    Location
    Michigan
    Posts
    172
    Corvette(s)
    1977 light blue
    Post Thanks / Like
    Rides
    0

    Default

    I have considered Vortec heads. You say GM still sells them drilled for my intake? I didn't know that..I have a Edlebrock performer I put on last spring, and would like to keep it. So do I contact a dealership for that? Do you know what compression that would give me? I've heard that used vortec heads from days gone by are often cracked. What say you?

  4. #4
    Administrator Tom Bryant's Avatar
    Join Date
    Nov 2000
    Location
    Edgerton, Ohio, United States
    Posts
    6,990
    Corvette(s)
    1959 black 270hp (9/2/69) 1981 Beige L81(10/20/80)
    Post Thanks / Like
    Rides
    2

    Default

    Well they used to but I can't find them now. They must have discontinued them. They require a Vortec manifold and if you are going to use an upgraded head I'd switch to a Performer RPM Intake. You can always sell the old one. They also require center bolt valve covers. I'm not sure what piston you have in the L48 but I suspect it's a dished one. CR will depend on dish volume, deck height, head gasket volume and combustion chamber volume.

    My combo in my '69 stepside is a .030 overbore, flat top pistons and ported smogger heads that have been milled some and cc'd to 73 cc chambers. The block isn't decked and I run a .018 shim head gasket so with the deck height figured in I arrive at just over 9.3:1 cr. That would be a premium fuel engine with a performance timing curve. Cam is a 214/224 @ .050, .442/.465 lift with a Turbo 400 and 3.73 rear gears.

    We would need the dish volume of your pistons to roughly calculate the cr with the Vortec heads. I suspect you would be safe though. These Vortec heads came stock on the L31 engine used in light trucks in the late 90s and up a few years. I had a L31 in my '99 Tahoe and it was strong. Leased it for 3 years and never had a problem so I can't speak to the cracking thing. For less than another $200.00 you might consider the aluminum Edelbrock E-Street heads EDL-5073 (70cc) or EDL=5089 (64cc) in the Summit catalog. They are a little bigger in runner volume but not too big for a mild build. I'm pretty sure they use the standard Chevy intake and valve covers so you can use what you already have.

    If you have flat top pistons I'd run the 70cc with a thicker composite head gasket or the 64cc with the dished pistons and in either case, the gasket Edelbrock recommends.

    Tom
    NCRS 1360.............SACC 2082.............C1 Registry..............L81 Registry
    1959 Chevrolet Corvette 1981 Chevrolet Corvette , 350 L81 automatic Frost Beige

  5. #5
    Member stevolwevol's Avatar
    Join Date
    May 2015
    Location
    Michigan
    Posts
    172
    Corvette(s)
    1977 light blue
    Post Thanks / Like
    Rides
    0

    Default

    Hey Tom, thanks for the info. I may look into the EDL 5073 heads from Summit. My guess is they will breath best, and give me better performance than vortecs anway. BTW, can you suggest a nice cam to complement the heads?

  6. #6
    Administrator Tom Bryant's Avatar
    Join Date
    Nov 2000
    Location
    Edgerton, Ohio, United States
    Posts
    6,990
    Corvette(s)
    1959 black 270hp (9/2/69) 1981 Beige L81(10/20/80)
    Post Thanks / Like
    Rides
    2

    Default

    If you are running a stock exhaust you want to stay mild with the cam. Looking at the charts Edelbrock shows the 2102 Cam as matched to your intake and the E-Street heads. Power increases up to 5500 rpm which they also list as the limit for the E-Street heads. Says major improvements in throttle response and torque from off idle to 5500 rpm. If you have dished pistons you will be in the 8'5 range with the 70 cc heads and might still be able to run regular. E85 would also work well.
    NCRS 1360.............SACC 2082.............C1 Registry..............L81 Registry
    Likes irongate liked this post
    1959 Chevrolet Corvette 1981 Chevrolet Corvette , 350 L81 automatic Frost Beige

  7. #7
    Member stevolwevol's Avatar
    Join Date
    May 2015
    Location
    Michigan
    Posts
    172
    Corvette(s)
    1977 light blue
    Post Thanks / Like
    Rides
    0

    Default

    I called Eckler's, they and the EDL 5073 heads you described for a little over 1000 dollars. They also had Promax heads for about $800. My compression would be about 9.3 for the more expensive heads, and I would be under 9:1 with the Promax heads. Ya get what you pay for. As far as my exhaust I have full length headers with "1 5/8 primary tubes. They should be fine for the upgrades I'm looking at doing. The tech told me; if I have too much cam, my vacuum will be too low operate the headlights etc. Now back in 1970 the L46, and the LT-1 put out 350 hp, and 370 hp. Both had vacuum powered headlights, and 2" diameter ram horn exhaust manifolds. Shouldn't I be able to put out that kind of power with my engine without making it less drivable?

  8. #8
    Administrator Tom Bryant's Avatar
    Join Date
    Nov 2000
    Location
    Edgerton, Ohio, United States
    Posts
    6,990
    Corvette(s)
    1959 black 270hp (9/2/69) 1981 Beige L81(10/20/80)
    Post Thanks / Like
    Rides
    2

    Default

    Well both of those engines had higher compression but you make a good point. You could go with a bigger cam than what we were talking about and still have enough vacuum. The Performer cam is matched to your heads and intake so it should be a nice package. Even better with the exhaust upgrades.

    Tom
    NCRS 1360.............SACC 2082.............C1 Registry..............L81 Registry
    1959 Chevrolet Corvette 1981 Chevrolet Corvette , 350 L81 automatic Frost Beige

Similar Threads

  1. "best aftermarket heads?"
    By sxyvet in forum C4 Technical and Performance
    Replies: 10
    Last Post: 03-03-06, 10:28 PM
  2. "best aftermarket heads & cams available"?
    By sxyvet in forum C4 Technical and Performance
    Replies: 13
    Last Post: 12-10-05, 12:26 AM
  3. Replace Head Gasket Or Go Aftermarket Heads
    By EOLIVER in forum C4 Technical and Performance
    Replies: 5
    Last Post: 12-31-04, 07:50 PM
  4. aftermarket heads for an LT4 turned 383 stroker
    By jcook00 in forum LT4 Forum
    Replies: 6
    Last Post: 09-24-03, 03:38 PM
  5. L82 heads v aftermarket
    By sd pacecar in forum C3 Technical and Performance
    Replies: 2
    Last Post: 01-23-02, 09:20 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •