Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Member
    Join Date
    Jun 2004
    Location
    St. Louis, MO
    Posts
    122
    Post Thanks / Like
    Rides
    0

    Default How to build a wood body dolly?

    Does anyone have the plans to build a wood body dolly for a C-2? I like the ones you can buy for $700 ($825 shipped) but, money may be saved to build my own.
    Thanks, Kurt

  2. #2
    Member henny496's Avatar
    Join Date
    Jul 2004
    Location
    Beaverton Ontario
    Posts
    318
    Post Thanks / Like
    Rides
    0

    Default

    Hi Kurt
    I have built a wood dolly and I just used the GM chassis blueprint for my measurements. If you want I can draw something and e-mail or fax it to you.
    Someone out there may have a better system than what I used. This was cheap and worked OK. Do you have to roll it around on grass or gravel, or will it only be on concrete? Uneven ground may warrant a stronger set up to help the body from flexing

    take care
    Tom

  3. #3
    Member
    Join Date
    Jun 2004
    Location
    St. Louis, MO
    Posts
    122
    Post Thanks / Like
    Rides
    0

    Default

    Tom. I suspect I will only be on hard surfaces. I have to get it up on a trailer to be blasted (remove paint), then back to a garage for painting. The main section under the bird cage will not be tough to make, it's the front end that may be a trick to support. Thanks, Kurt

  4. #4
    How to build a wood body dolly? 67HEAVEN's Avatar
    Join Date
    Nov 2001
    Location
    SouthCentral Ontario
    Posts
    5,980
    Post Thanks / Like
    Rides
    0

    Default

    Noland Adams Body Lift Workbook is available in the Store at www.NCRS.org.



    $9.00 is what I paid. It includes plans and a material list for building a wooden dolly.

  5. #5
    Member Dave65's Avatar
    Join Date
    Feb 2003
    Location
    Cincinnati, Ohio
    Posts
    109
    Post Thanks / Like
    Rides
    0

    Default

    Kurt,

    These drawings are probably barely legible but are what I used to build the body dolly shown below. They are from the NCRS CD and were in the Restorer in the mid 80's. I put it on jack stands to clean/work under the body.







    I would check the dimensions to the frame drawing. Sorry about the quality - it is the best I have and is what I used.

    Dave

  6. #6
    Member
    Join Date
    Jun 2004
    Location
    St. Louis, MO
    Posts
    122
    Post Thanks / Like
    Rides
    0

    Default

    Dave, That looks easy to make... I wish I could read all the measurements. Could you email it to me??? Please and Thank you.. Kurt kkobusch@charter.net

  7. #7
    Member
    Join Date
    Jul 2003
    Location
    Nebraska
    Posts
    35
    Post Thanks / Like
    Rides
    0

    Default

    Dave,

    I would like to have a copy of those measurements too. My email address is

    gregm@cashwa.com

    Thank You

    Greg
    60fuelie

Similar Threads

  1. Body Mount Install - Lessons Learned...
    By wrc3 in forum C3 Technical and Performance
    Replies: 21
    Last Post: 12-17-16, 11:19 AM
  2. Body Dolly Blueprint
    By 61 Silver in forum C1 & C2 General and Technical Discussion
    Replies: 3
    Last Post: 11-29-04, 06:24 PM
  3. Coolest Body Dolly ever !! Just got it today!
    By 1964*Coupe in forum C1 & C2 General and Technical Discussion
    Replies: 2
    Last Post: 10-14-04, 08:33 PM
  4. Body Dolly
    By JLMvette73 in forum C3 Technical and Performance
    Replies: 2
    Last Post: 07-31-03, 03:17 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •