Corvette Action Center - The ultimate online hub of Corvette news and information! Click here to go to to the 2014 C7 Corvette Center

Supporting Vendors / Dealers - Supporting Membership - Advertising Information
Page 1 of 2 12 LastLast
Results 1 to 15 of 19

Thread: osb board on walls

  1. #1
    Member
    Join Date
    Jan 2001
    Location
    7259 west chester ohio 45069
    Posts
    167
    Corvette(s)
    1978 L82 BLACK

    Default osb board on walls

    I built my garage this past summer, instead of drywalling it I insulated it and put osb board on the walls wasn't much more than drywall, I than painted the walls white, really helps with the lighting. The reason I used the osb board was I can hang anything on the walls without trying to hit a stud, so far I am very pleased I went the route I did.

  2. #2
    Dave L.
    Guest

    Default

    mytoy - what is osb board? I am looking into doing my walls this summer. Sounds interesting,got any pictures by chance?

    Dave

  3. #3
    Registered User 68Roadster's Avatar
    Join Date
    Dec 2002
    Location
    Dallas, TX
    Posts
    1,596
    Corvette(s)
    '68 White Vert '05 Silverado SS

    Default

    Dave,
    OSB is oriented strain board.....you can get it at the Home Depot, etc for about 5 - 6 bucks a 4 x 8 sheet. Comes in varying thicknesses and is made from wood chips/pieces, glued and compressed together. Most builders use it on roofs these days instead of expensive plywood.
    Not as smooth as sheetrock but alot stronger.....

  4. #4
    Member
    Join Date
    Jan 2001
    Location
    7259 west chester ohio 45069
    Posts
    167
    Corvette(s)
    1978 L82 BLACK

    Default Dave

    Dave, 68 roadster is correct about the osb board, I paid about 5.84 for it, it also makes your garage alot stronger, so far I haven't notice any pitfalls.

  5. #5
    Member
    Join Date
    Jan 2003
    Location
    New York
    Posts
    17

    Default

    If the garage is attatched I do not believe it will pass the building code in most states. I have an attached garage offset from the back of my home
    (only 10 feet attached) and was told that I must use 5/8" sheetrock on all surfaces to pass fire code. I will be placing the OSB under the sheetrock on the walls for the reason mrtoy mentioned. A little extra expense, but worth it IMO.
    Joe

  6. #6
    Member JonM's Avatar
    Join Date
    Mar 2002
    Location
    East Haven, CT- USA
    Posts
    4,567
    Corvette(s)
    84 Coupe

    Default

    Let me interject a little, the 5/8 th inch sheetrock is correct. However, its usually only needed where the house is connected to the garage including the attic space. The rest of the walls can be half inch. Also for those of you who are going to put the OSB and the sheetrock up, remember now you will have to buy special door jambs or cut extentions.

  7. #7
    Member supernatural400's Avatar
    Join Date
    Feb 2001
    Location
    massachusetts
    Posts
    881
    Corvette(s)
    1993 SuperNatural 400 #5 /99 LS1 Z28 N2O equipped

    Default

    I used 3/8 plywood on all my walls for the same reason, building codes, we don't need no stinking building codes. Not sure how they would find out unless you happen to tell the building inspector

  8. #8
    Member JonM's Avatar
    Join Date
    Mar 2002
    Location
    East Haven, CT- USA
    Posts
    4,567
    Corvette(s)
    84 Coupe

    Default

    I can explain how they find out...If you happen to have a fire in the garage, and it spreads into the main house and distroys it. The insurance company comes in looks at the wall and sees no 5/8 in sheet rock on the walls. They then go to the local inspector to see if he signed off on the sheetrock. If he didn't and you did not follow code, now they have an excuse to not pay your claim. And on top of it, its good protection for your familly. They may need that extra 30 minutes to wake up and get out.

    Originally posted by supernatural400
    I used 3/8 plywood on all my walls for the same reason, building codes, we don't need no stinking building codes. Not sure how they would find out unless you happen to tell the building inspector

  9. #9
    Dave L.
    Guest

    Default

    My garage is not connected to the house. Do you think I need a building permit to put up insulation and osb board in my garage? It seems to me another reason for a building permit is to alert the township that they need to raise my property taxes.
    http://corvetteactioncenter.com/foru...&postid=177071

    Dave

  10. #10
    Member supernatural400's Avatar
    Join Date
    Feb 2001
    Location
    massachusetts
    Posts
    881
    Corvette(s)
    1993 SuperNatural 400 #5 /99 LS1 Z28 N2O equipped

    Default

    Originally posted by JonM
    I can explain how they find out...If you happen to have a fire in the garage, and it spreads into the main house and distroys it. The insurance company comes in looks at the wall and sees no 5/8 in sheet rock on the walls. They then go to the local inspector to see if he signed off on the sheetrock. If he didn't and you did not follow code, now they have an excuse to not pay your claim. And on top of it, its good protection for your familly. They may need that extra 30 minutes to wake up and get out.
    You simply explain that it was like that when you bought the house, unless you happen to build the garage after you bought it.
    Most states as far as I know require no building permit for interior walls unless there load bearing and if you do the work yourself and are not a licensed contrator you do not need it inspected. I just went thru that with some electrical work on my garage. Maybe different since my garage is not attached. Of course in my case I would be more worried about the 5 lbs of gunpower, boxes of primers and a few thousand rounds of ammo going off before the walls went up Of course each town is different they set there own building codes

  11. #11
    Member supernatural400's Avatar
    Join Date
    Feb 2001
    Location
    massachusetts
    Posts
    881
    Corvette(s)
    1993 SuperNatural 400 #5 /99 LS1 Z28 N2O equipped

    Default

    Originally posted by BURGLAR
    My garage is not connected to the house. Do you think I need a building permit to put up insulation and osb board in my garage? It seems to me another reason for a building permit is to alert the township that they need to raise my property taxes.
    http://corvetteactioncenter.com/foru...&postid=177071

    Dave
    it's a town thing, you don't need a permit for insulation, in fact you don't need any if you don't want it

  12. #12
    Member
    Join Date
    Jan 2001
    Location
    7259 west chester ohio 45069
    Posts
    167
    Corvette(s)
    1978 L82 BLACK

    Default permits

    I live in southern Ohio, between Cincinnati and Dayton , I had to have a zoning permit, building permit with three inspection and a electrical permit, when the inspector was here for the inspection I mention that I was putting up osb board and he didn't say a word. I do know in our county you have to have a permit and a inspection to install insulation in a new home but not on a detached garage

  13. #13
    Supporting Member Vanity Plate Bob's Avatar
    Join Date
    Apr 2002
    Location
    Johnstown, Pa, USA
    Posts
    2,471

    Default

    Just what I heard. Yesterday. In Cambria and Somerset Counties, at least, in Pa. They, whomever, supposedly went around and documented all asbestos in commercial buildings.
    If they come around and ck and some changes have been made and the asbestos is missing they want to know where it is. All removed asb. must be double bagged and marked with your name. If the land where it is disposed of, legally, is changed years down the road the guys name on the bag is responsible for having it properly moved.
    The teller is a contractor. Just what he said.

  14. #14
    Administrator Tom Bryant's Avatar
    Join Date
    Nov 2000
    Location
    Edgerton, Ohio, United States
    Posts
    8,930
    Corvette(s)
    1959 black 270hp (9/2/69) 1981 Beige L81(10/20/80)

    Default

    OBS is great for shop walls. I used to help a friend in a shop done that way. A business too, but in rural NE Indiana they don't have no stinkin' building inspectors.

    Here in NW Ohio I used drywall in my shop because I wanted a nice finished look with wood trim and the whole thing. All I had to get was a building permit. No electrical (could have even done it myself) or inspections. When I built the house only the health department came out to inspect the septic system. There are advantages in living out in fly over country.

    Tom

  15. #15
    Member supernatural400's Avatar
    Join Date
    Feb 2001
    Location
    massachusetts
    Posts
    881
    Corvette(s)
    1993 SuperNatural 400 #5 /99 LS1 Z28 N2O equipped

    Default

    When I had my heaters installed. I needed to get the gas fittings inspected, but the heating contractor said if I did the electrical myself, not only would I save money but I am not required to get a electrical inspection done since I am the home owner and doing it myself, If he did it being a contractor he would be required to get a permit and have and inspection done

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© CORVETTE is a registered trademark of the General Motors Corporation & Chevrolet Motor Division.  Neither Chevrolet Motor Division nor any subsidiaries of GM© shall bear any responsibility for CorvetteActionCenter.com content, comments, or advertising. CorvetteActionCenter.com is independent from GM© and is not affiliated with, sponsored or supported by GM©.  Copyright/trademark/sales mark infringements are not intended, or implied.  All Rights Reserved