Corvette Action Center - The ultimate online hub of Corvette news and information! Click here to go to the Corvette Forums!

Supporting Vendors / Dealers - Supporting Membership - Advertising Information - Corvette Amazon Shop
Results 1 to 3 of 3
  1. #1
    hall117
    Guest

    Default Vette won't start, ecm code 46

    Help! My vette won't start and the ecm is putting out a code 46 which the vechile anit theft system (VATS) but I don't know where it's at or how to trouble shoot it? Is VATS a module or computer or relay and where can I find it.

  2. #2
    Rob
    Site Administrator Rob's Avatar
    Join Date
    Sep 2000
    Location
    "Manchestah" NH
    Posts
    24,706
    Corvette(s)
    1990 ZR-1 (Canadian) Bright Red / Black

    Default

    Welcome to the Corvette Action Center.

    If you intend on servicing your Corvette on your own, I strongly recommend that you pick up a 1991 Service Manual. You can pick one up from Helm, MidAmerica, Ecklers and other vendors. For a full list, check the <a href="http://www.corvetteactioncenter.com/portal/index.php?cat=29&t=sub_pages">Parts and Service Manuals</a> section in our Corvette Portal.

    According to the service manual, Code 46 is the Vehicle Anti-Theft System (VATS).

    From the service manual:
    Test Description: Numbers below refer to circled numbers on the diagnostic chart.
    [list=1][*]If the engine cranks but doesn't start, it indicates that the portion of the CCM which generates the signal to the ECM is not operating or the 229 CKT is open or shorted to ground. If the CCM module is found to be OK, as determined from the Central Control Module (CCM) (Section 8D), the ECM may be at fault, but this is not a likely condition.[*]If the engine will not crank, it indicates that there is a VATS problem or an incorrect key or starting procedure is being used.[/list=1]
    The VATS lock cylinder is located where you place the ignition key. At this point, if you're going to pursue the repair, again, I strongly urge you to pick up a service manual as there are diagrams and instructions in there for proper diagnosis and repair. However, given the lag time seen in ordering service manuals due to backorders at some vendors, you may want to consider having the vehicle towed to your nearest Chevrolet dealership and have them work on it. Hope this helps.
    Rob Loszewski, Owner & Site Administrator
    Corvette Action Center
    Cadillac V-Net
    Cadillac XLR Net
    The Meadery
    Torque Network
    VetteTube
    NCRS Member #27792
    "Let your plans be dark and impenetrable as night, and when you move, fall like a thunderbolt." - Sun Tzu


  3. #3
    Drewser
    Guest

    Default VATS

    Welcome Hall117,

    I am a locksmith and work on VATS all the time. You basically have a little resistor on your key (the little pellet) that comes in contact with two little brass plates inside your ignition. There are two fine little wires that connect the key to the module. These wires are very prone to break and fatigue. I would start there, but the problem here is that you have to be good at pulling steering wheels which entails using wheel pullers and lockplate compressors, pulling your turn signals and possibly and airbag (if so equipped, I forget if the 91 has an airbag) just to get to the ignition and then you have to be VERY careful that you don't break the wires while inspecting them. I have a tool called a VATS decoder/interrogator that I can either plug into the keyhole or the module to diagnose exactly where your problem is. Any good locksmith will have one. I would give a 'smith a shot at the work before I trusted a dealer, unless you have a good dealer. They are gonna want to gig you for something no matter what your problem is (if they are anything like OUR local dealer).

    Let me know if you need any more info. Key are my life man.

Similar Threads

  1. Upgrading an 85 ECM with a 98 ECM in an 85 Vette
    By Willycool in forum C4 Technical and Performance
    Replies: 8
    Last Post: 09-30-02, 01:30 AM
  2. ECM Code 15
    By Rocketkid in forum C3 Technical and Performance
    Replies: 4
    Last Post: 02-15-02, 06:29 AM
  3. 1988 Vette Rims And Rpo Code
    By LONNIE in forum C3 Technical and Performance
    Replies: 5
    Last Post: 01-14-02, 04:10 PM
  4. ECM code P1416 "Service Engine" light
    By LT4SilverEagle in forum C4 Technical and Performance
    Replies: 6
    Last Post: 08-03-01, 04:37 PM
  5. 1986 code 34 problems
    By TR3MGTD in forum C4 Technical and Performance
    Replies: 7
    Last Post: 06-24-01, 08:28 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
© CORVETTE is a registered trademark of the General Motors Corporation & Chevrolet Motor Division.  Neither Chevrolet Motor Division nor any subsidiaries of GM© shall bear any responsibility for CorvetteActionCenter.com content, comments, or advertising. CorvetteActionCenter.com is independent from GM© and is not affiliated with, sponsored or supported by GM©.  Copyright/trademark/sales mark infringements are not intended, or implied.  All Rights Reserved